RAK19009 WisBlock Mini Base Board with Power Slot Installation Guide
RAK19009 WisBlock Base Board is the main board that allows you to attach MCU, sensors, and IO modules through the standardized expansion connectors. These connectors provide a data bus interconnection between the modules attached to the RAK19009 Base Board.
Prerequisite
Required items for RAK19009 setup include:
- RAK19009 WisBlock Mini Base Board with Power Slot
- A compatible WisBlock Power Module
- A compatible WisBlock Core
- Compatible WisBlock Modules
Refer to the dedicated Quick Start Guide of each WisBlock module for detailed instructions on running examples and uploading code to the WisBlock Core.
WisBlock WisConnector Installation
Attaching a WisConnector
The WisConnector is the interface between the Wisblock Base module and the WisBlock Core, Sensor, and IO modules. Before connecting these modules, read the following instructions:
Figure 1: Notation within the guide- Align the connectors. Keep the header parallel and place it lightly in the corresponding lap joint of the socket.
Figure 1: Alignment of WisConnector- Fit the connector. Tilt one end of the connector (header) less than 20 degrees, while do not apply force during this process, gently place the other end in parallel.
Figure 1: Fit the WisConnector’s header inside of the socket- After the above alignment steps, the header and socket are matched but still not buckled.
Figure 1: WisConnector’s header matched inside of the socket- Apply forces evenly by pressing in parallel, then there will be a sound confirming the completion of the buckling.
Figure 1: Apply forces to buckle the heard to the socket- In the process of buckling and applying force, avoid the application of uneven force on both sides.
Figure 1: Avoid applying uneven forces- When the buckling process is completed, check that the header and socket are kept in parallel.
Figure 1: Correct way to buckle the WisConnector’s header to the socket- If after buckling, the header and socket are not in a parallel state (not fully assembled in one place), then press the even force on both sides of the long side to complete the correct buckling.
Figure 1: WisConnector’s header is not parallel to the socket- When the aforementioned steps are not completed yet, do not apply force to buckle. Otherwise, there will be a risk to damage the connector. When the connector cannot be smoothly buckled down, repeat the alignment step.
Detaching a WisConnector
- To disconnect the header from the socket, pull out in parallel with even forces.
Figure 1: Correct way: Applying even forces to detach the header from the socket- Avoid pulling out the header asymmetrically in the long-side direction.
Figure 1: Wrong way: Applying uneven forces to detach the header from the socket- The short-side of the connector can be pulled out asymmetrically, but apply the force vertically and avoid rotating the header.
Figure 1: Wrong way: Do not rotate the header- Avoid applying forces in a single corner.
Figure 1: Wrong way: Do not apply force in a single corner of the headerWisBlock Module Installation
Assembling a WisBlock Module
WisBlock Core
Install the WisBlock Core module in the CPU slot on the RAK19009 Base Board. The CPU slot is identified by the board silkscreen. Use the WisBlock WisConnector Installation procedure to attach the module.
Secure the installed WisBlock Core with one or more M1.2 x 3 mm screws, depending on the WisBlock Core model.
Figure 1: WisBlock Core slot on the RAK19009 Mini Base Board with Power SlotWisBlock Power
Install the WisBlock Power Module in the dedicated Power slot on the RAK19009 Base Board. The Power slot is identified by the board silkscreen. Use the WisBlock WisConnector Installation procedure to attach the module.
Secure the installed WisBlock Power Module with one or more M1.2 x 3 mm screws, depending on the Power Module design.
Figure 1: WisBlock Power slot on the RAK19009 Mini Base Board with Power SlotWisBlock Sensor
A WisBlock Sensor module is designed to be installed on the Sensor slot of the RAK19009 Base Board. There are two (2) available sensor slots in the RAK19009 Base Board. The location of the slots is properly marked by silkscreen.
Follow carefully the procedure of the section, attaching a WisConnector , to attach a WisBlock Sensor module. Once attached, fix the module with an M1.2 x 3 mm screw.
Figure 1: WisBlock Sensor slots on the RAK19009 Mini Base Board with Power SlotDisassembling a WisBlock Module
- Remove the screws securing the WisBlock module.
Figure 1: Removing screws from a WisBlock module- Once the screws are removed, on the PCB of a WisBlock module, there is a silkscreen that shows the correct location where force can be applied. By applying even force under the marked area, the module can be detached from the Base Board.
Figure 1: WisBlock module detaching area
Figure 1: Detaching a WisBlock module from the RAK19009 Base Board