RAK19011 WisBlock Dual IO Base Board with Power Slot Installation Guide
The RAK19011 WisBlock Dual IO Base Board with Power Slot is the main board for attaching MCUs, power modules, sensors, and IO modules via standardized expansion connectors. These connectors provide data bus interconnection between the attached modules.
Prerequisite
Required items for RAK19011 setup include:
- RAK19011 WisBlock Dual IO Base Board with Power Slot
- A compatible WisBlock Power Module
- A compatible WisBlock Core
- Compatible WisBlock Modules
Refer to the dedicated Quick Start Guide of each WisBlock module for detailed instructions on running examples and uploading code to the WisBlock Core.
Safety Information
- RAK19011 requires a WisBlock power module for power and connector interfaces. It lacks USB and battery/power connectors; these functionalities must be added using an appropriate WisBlock power module.
- Secure all installed modules with the required screws to ensure reliable operation.
WisBlock WisConnector Installation
The RAK19011 WisBlock Dual IO Base Board with Power Slot is the main board for attaching MCUs, power modules, sensors, and IO modules via standardized expansion connectors. These connectors provide data bus interconnection between the attached modules.
Attaching a WisConnector
The WisConnector is the interface between the Wisblock Base module and the WisBlock Core, Sensor, and IO modules. Before connecting these modules, read the following instructions:
Figure 1: Notation within the guide- Align the connectors. Keep the header parallel and place it lightly in the corresponding lap joint of the socket.
Figure 1: Alignment of WisConnector- Fit the connector. Tilt one end of the connector (header) less than 20 degrees, while do not apply force during this process, gently place the other end in parallel.
Figure 1: Fit the WisConnector’s header inside of the socket- After the above alignment steps, the header and socket are matched but still not buckled.
Figure 1: WisConnector’s header matched inside of the socket- Apply forces evenly by pressing in parallel, then there will be a sound confirming the completion of the buckling.
Figure 1: Apply forces to buckle the heard to the socket- In the process of buckling and applying force, avoid the application of uneven force on both sides.
Figure 1: Avoid applying uneven forces- When the buckling process is completed, check that the header and socket are kept in parallel.
Figure 1: Correct way to buckle the WisConnector’s header to the socket- If after buckling, the header and socket are not in a parallel state (not fully assembled in one place), then press the even force on both sides of the long side to complete the correct buckling.
Figure 1: WisConnector’s header is not parallel to the socket- When the aforementioned steps are not completed yet, do not apply force to buckle. Otherwise, there will be a risk to damage the connector. When the connector cannot be smoothly buckled down, repeat the alignment step.
Detaching a WisConnector
- To disconnect the header from the socket, pull out in parallel with even forces.
Figure 1: Correct way: Applying even forces to detach the header from the socket- Avoid pulling out the header asymmetrically in the long-side direction.
Figure 1: Wrong way: Applying uneven forces to detach the header from the socket- The short-side of the connector can be pulled out asymmetrically, but apply the force vertically and avoid rotating the header.
Figure 1: Wrong way: Do not rotate the header- Avoid applying forces in a single corner.
Figure 1: Wrong way: Do not apply force in a single corner of the headerWisBlock Module Installation
Assembling a WisBlock Module
WisBlock Core
A WisBlock Core module is designed to be installed on the CPU slot of the RAK19011 WisBlock Dual IO Base Board with Power Slot. The slot location is identified by the board silkscreen. Use the WisBlock WisConnector Installation procedure to attach the module.
Once attached, fix the module with one or more pieces of M1.2 x 3 mm screws depending on the WisBlock Core.
Figure 1: WisBlock Core slot on the RAK19011 Base BoardWisBlock Power
A WisBlock Power module is designed to be installed on the Power slot of the RAK19011 WisBlock Dual IO Base Board with a Power Slot. The slot location is identified by the board silkscreen. Use the WisBlock WisConnector Installation procedure to attach the module.
Once attached, fix the module with one or more pieces of M1.2 x 3 mm screws depending on the WisBlock Core.
Figure 1: WisBlock Power slot on the RAK19011 Base BoardWisBlock Sensor
A WisBlock Sensor module is designed to be installed on the sensor slot of the RAK19011 WisBlock Dual IO Base Board with Power Slot. There are six (6) available sensor slots in the RAK19011 WisBlock Dual IO Base Board with Power Slot. The sensor slot locations are properly marked by the silkscreen. Follow carefully the procedure of the section, attaching a WisConnector, to attach a WisBlock Sensor module. Once attached, fix the module with an M1.2 x 3 mm screw.
Figure 1: WisBlock Sensor slots on the RAK19011 Base BoardWisBlock IO
A WisBlock IO module is designed to be installed on the IO slot of the RAK19011 WisBlock Dual IO Base Board with Power Slot. There are two (2) IO slots in the RAK19011 WisBlock Dual IO Base Board with Power Slot. The IO slot locations are properly marked by the silkscreen. Follow carefully the procedure of the section, attaching a WisConnector, to attach a WisBlock IO module. Once attached, fix the module with three pieces of M1.2 x 3 mm screws.
Figure 1: WisBlock IO slots on the RAK19011 Base BoardDisassembling a WisBlock Module
- Remove the screws securing the WisBlock module.
Figure 1: Removing screws from a WisBlock module- Once the screws are removed from a WisBlock module's PCB, a silkscreen indicates the correct location to apply force. Applying even force under the marked area detaches the module from the base board.
Figure 1: WisBlock module detaching area
Figure 1: Detaching a WisBlock module from the RAK19011 Base Board