RAK2247 Pi HAT Datasheet
Overview
Description
RAK2247 Pi HAT is a converter board designed to allow the RAK2247 Concentrator module to interface with a Raspberry Pi SBC. It maps the 52-pin of mPCIe RAK2247 connector to the 40-pin Raspberry Pi header.
Moreover, there is a GPS on the HAT that enhances your RAK2247 with localization and timing data.
Features
- Pi HAT form factor
- mPCIe slot
- GPS Module (MAX-7Q) module integrated into the HAT
Package Inclusion
- One (1) RAK2247 Pi HAT
Specifications
Overview
Block Diagram
The RAK2247 Pi HAT maps the RAK2247 pins from the 52-pin mPCIe connector to the 40-pin Raspberry Pi connector. Refer to the block diagram in figure 1 below and the pin mapping table in the following section – Pin Definition.
Figure 1: RAK2247 Pi HAT Block DiagramHardware
Pin Definition
Figure 1: RAK2247 Pi HAT Pinout DiagramThe following tables show the pin definitions and the description of the RAK2247 Pi HAT on the 40-Pin Pi HAT connector:
| Type | Description |
|---|---|
| IO | Bidirectional |
| DI | Digital input |
| DO | Digital input |
| OC | Open collector |
| OD | Open drain |
| PI | Power input |
| PO | Power input |
| NC | No Connection |
| Pin No. | Raspberry Pi 40-Pin Connector | RAK2247 Pi HAT PIN | I/O | Remarks |
|---|---|---|---|---|
| 1 | 3V3 | NC | No Connection | |
| 2 | 5 V | 5 V | PI | 5 V Input |
| 3 | GPIO2 (SDA1) | I2C_SDA | IO | HOST SDA, Connect RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s SDA |
| 4 | 5 V | 5 V | PI | 5 V Input |
| 5 | GPIO3 (SCL1) | I2C_SCL | IO | HOST SCL, Connect RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s SCL |
| 6 | GND | GND | Ground | |
| 7 | GPIO4 (GPIO_GCLK) | NC | No Connection | |
| 8 | GPIO14 (TXD0) | UART_RXD_ MAX-7Q | DI | Connect RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s UART_RXD |
| 9 | GND | GND | Ground | |
| 10 | GPIO15 (RXD0) | UART_TXD_ MAX-7Q | DO | Connect to RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s UART_TXD |
| 11 | GPIO17 (GPIO_GEN0) | RESET_RAK2247 | DI | Connect to SX1301’s RESET PIN, SX1301 reset input, Active high, ≥100 ns for SX1301 reset |
| 12 | GPIO18 (GPIO_GEN1) | NC | No Connection | |
| 13 | GPIO27 (GPIO_GEN2) | NC | No Connection | |
| 14 | GND | GND | Ground | |
| 15 | GPIO22 (GPIO_GEN3) | NC | No Connection | |
| 16 | GPIO23 (GPIO_GEN4) | NC | No Connection | |
| 17 | 3V3 | NC | No Connection | |
| 18 | GPIO24 (GPIO_GEN5) | NC | No Connection | |
| 19 | GPIO10 (SPI_MOSI) | SPI_MOSI | DI | Host SPI MOSI |
| 20 | GND | GND | Ground | |
| 21 | GPIO9 (SPI_MISO) | SPI_MISO | DO | Host SPI MOSI |
| 22 | GPIO25 (GPIO_GEN6) | NC | No Connection | |
| 23 | GPIO11 (SPI_CLK) | SPI_CLK | DI | Host SPI CLK |
| 24 | GPIO8 (SPI_CE0_N) | SPI_CE | DI | Host SPI CS |
| 25 | GND | GND | Ground | |
| 26 | GPIO7 (SPI_CE1_N) | NC | No Connection | |
| 27 | ID_SD | NC | No Connection | |
| 28 | ID_SC | NC | No Connection | |
| 29 | GPIO5 | NC | No Connection | |
| 30 | GND | GND | Ground | |
| 31 | GPIO6 | NC | No Connection | |
| 32 | GPIO12 | NC | No Connection | |
| 33 | GPIO13 | RESET_GPS_ MAX-7Q | DI | Connect to RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s RESET, GPS module MAX-7Q reset inputs, Active High |
| 34 | GND | GND | Ground | |
| 35 | GPIO19 | STANDBY_GPS_ MAX-7Q | DI | Connect to RAK2247 Pi HAT built in GPS Module (MAX-7Q)’s STANDBY, GPS module MAX-7Q external interrupt input, Active High |
| 36 | GPIO16 | NC | No Connection | |
| 37 | GPIO26 | NC | No Connection | |
| 38 | GPIO20 | NC | No Connection | |
| 39 | GND | GND | Ground | |
| 40 | GPIO21 | NC | No Connection |
Ordering Information
| Model | Description | Supported Module |
|---|---|---|
| RAK2247 Pi HAT | mPCIe to 40-pin Pi HAT Convert Board for RAK2247 module with SPI interface | RAK2247 SPI module |
