RAK19003 WisBlock Mini Base Board Installation Guide
RAK19003 WisBlock Base Board is the main board that allows you to attach MCU, sensors, and IO modules through the standardized expansion connectors. These connectors provide a data bus interconnection between the modules attached to the RAK19003 Base Board.
This guide provides the requirements and procedures for installing and removing WisBlock modules and connecting supported power sources to the RAK19003.
Prerequisite
Required items for RAK19003 WisBlock Mini Base Board setup include:
-
Your choice of WisBlock Core
-
Your choice of WisBlock Modules
NOTERefer to the documentation for the WisBlock module used in your application for module-specific setup instructions and example code.
-
Type-C USB cable for programming and debugging
WisBlock WisConnector Installation
Attaching a WisConnector
The WisConnector is the interface between the Wisblock Base module and the WisBlock Core, Sensor, and IO modules. Before connecting these modules, read the following instructions:
Figure 1: Notation within the guide- Align the connectors. Keep the header parallel and place it lightly in the corresponding lap joint of the socket.
Figure 1: Alignment of WisConnector- Fit the connector. Tilt one end of the connector (header) less than 20 degrees, while do not apply force during this process, gently place the other end in parallel.
Figure 1: Fit the WisConnector’s header inside of the socket- After the above alignment steps, the header and socket are matched but still not buckled.
Figure 1: WisConnector’s header matched inside of the socket- Apply forces evenly by pressing in parallel, then there will be a sound confirming the completion of the buckling.
Figure 1: Apply forces to buckle the heard to the socket- In the process of buckling and applying force, avoid the application of uneven force on both sides.
Figure 1: Avoid applying uneven forces- When the buckling process is completed, check that the header and socket are kept in parallel.
Figure 1: Correct way to buckle the WisConnector’s header to the socket- If after buckling, the header and socket are not in a parallel state (not fully assembled in one place), then press the even force on both sides of the long side to complete the correct buckling.
Figure 1: WisConnector’s header is not parallel to the socket- When the aforementioned steps are not completed yet, do not apply force to buckle. Otherwise, there will be a risk to damage the connector. When the connector cannot be smoothly buckled down, repeat the alignment step.
Detaching a WisConnector
- To disconnect the header from the socket, pull out in parallel with even forces.
Figure 1: Correct way: Applying even forces to detach the header from the socket- Avoid pulling out the header asymmetrically in the long-side direction.
Figure 1: Wrong way: Applying uneven forces to detach the header from the socket- The short-side of the connector can be pulled out asymmetrically, but apply the force vertically and avoid rotating the header.
Figure 1: Wrong way: Do not rotate the header- Avoid applying forces in a single corner.
Figure 1: Wrong way: Do not apply force in a single corner of the headerWisBlock Module Installation
Assembling a WisBlock Module
WisBlock Core
Install the WisBlock Core module in the CPU slot on the RAK19003 Base Board, as indicated by the silkscreen. Follow the WisBlock WisConnector Installation procedure to attach the module correctly.
Once attached, secure the module with one or more M1.2 x 3 mm screws, depending on the WisBlock Core.
Figure 1: WisBlock Core silkscreen on the RAK19003 Base BoardWisBlock Sensor
A WisBlock Sensor module is designed to be installed on the Sensor slot of the RAK19003 Base Board. There are two (2) available sensor slots in the RAK19003 Base Board. Each slot is identified by the silkscreen. Follow the WisBlock WisConnector Installation procedure to attach the module, then secure it with an M1.2 x 3 mm screw.
Figure 1: WisBlock Sensor silkscreen on the RAK19003 Base BoardDisassembling a WisBlock Module
- The procedure for removing a WisBlock module is the same for the Core and Sensor modules. First, remove the screws securing the module.
Figure 1: Removing screws from the WisBlock module- Once the screws are removed, on the PCB of a WisBlock module, there is a silkscreen that shows the correct location where force can be applied. By applying even force under the marked area, the module can be detached from the Base Board.
Figure 1: Detaching silkscreen on the WisBlock module
Figure 1: Applying even force at the proper location to detach a WisBlock module from the Base BoardBattery Connection
RAK19003 can be powered via the USB cable or Li-Ion/LiPo battery via the dedicated connectors. The matching connector for the battery wires is a JST PHR-2 2 mm pitch female .
The battery can be recharged as well via a small Solar Panel. The matching connector for the solar panel wires is an JST ZHR-2 1.5 mm pitch female . The GND pin of Battery Connector is located on edge of the board.
-
Batteries can cause harm if not handled properly.
-
Only 3.7-4.2 V Rechargeable LiPo batteries are supported. It is highly recommended not to use other types of batteries with the system unless you know what you are doing.
-
If a non-rechargeable battery is used, it has to be unplugged first before connecting the USB cable to the USB port of the board to configure the device. Not doing so might damage the battery or cause fire.
-
Make sure the battery wires match the polarity indicated on the RAK19003 board. Not all batteries use the same wire polarity.
Solar Panel Connection
The full specification of Solar Panel Connection can be found on the datasheet of the WisBlock Base.
- Only 5 V solar panels are supported. Do not use 12 V solar panels. It will destroy the charging unit and eventually other electronic parts.
- The GND pin of the Solar Panel Connector is located on edge of the board. Make sure the Solar Panel wires are matching the polarity on the RAK19003 board.
